This tool is used to help generate the "string" needed for the options field.
e.g Static Talkgroups and Configurations in Pi-Star / MMDVM / DMRGateway.

Duplex Hotspots can use TS1 and/or TS2

Simplex Hotspots can only use TS2

Type in the Talk Groups and Settings you want.
Click "Generate Pi-Star Options"

Duplex: Simplex:

If you plan on using   Dial-a-TG   DO NOT set any Static Talk Groups on Slot 2

Timeslot 1
Timeslot 2
  TG 1 (leave 0 for none):   TG 1 (leave 0 for none):

 If using Dial-a-TG leave all as 0  

  TG 2 (leave 0 for none):   TG 2 (leave 0 for none):

 on Slot 2

  TG 3 (leave 0 for none):   TG 3 (leave 0 for none):
  TG 4 (leave 0 for none):   TG 4 (leave 0 for none):
  TG 5 (leave 0 for none):   TG 5 (leave 0 for none):

  Dial-a-TG  0 or TG
  Voice Identification    0 off or 1 on  
  Language  en_GB  
  Single Mode  0 off or 1 on  
  TG Timeout  Minutes




( Copy & paste the "string" when generated above into the "Options= field" in your device. )




Options Calculator by Jim Nessen K6JWN.




Explanation.

Pi-Star


*If you set ANY Static Talk Groups on Slot 1 or 2, YOU CAN not use it via Dial-a-TG.
Static Talk Group must be used via a Channel in your radio and not via Dial-a-TG.
Example:- If you set TG 2350 as Static, you can not use Dial-a-TG to talk on 2350.


TS1=2350,235;

Set Statics you want on Slot 1.  Separate each Talk Group with a comma.
You can not have the same Talk Group set as static on Slot 1 or Slot 2.
At the end of each section, you need a Semicolon.


TS2=2351,2352;

Set Statics you want on Slot 2.  Separate each Talk Group with a comma.
You can not have the same Talk Group set as static on Slot 1 or Slot 2.
At the end of each section, you need a Semicolon.


DIAL=91;

*see above

0=None. Set default Enhanced Talk Groups (Dial-a-TG) TG9 Slot 2.
Only One Talk Group can be entered in this section.
You can not have the same Talk Group set as static on Slot 1 or Slot 2.
At the end of each section, you need a Semicolon.


TIMER=10;

Time a Talk Group is held active for.  Pressing your PTT on a Talk Group reset this timer.
You select any number of minutes you like here.  But the recommended time is 10 or 5 mins.
If setting more than two static to a slot, you might wish to set Timer to  1 or 2 min.
At the end of each section, you need a Semicolon.


VOICE=0;

0=OFF  1=ON.  15 minute Voice Ident can be set ON or OFF on Time Slot 2.
Radios will RX from the network, "This is CALL-SIGN FreeDMR. "
At the end of each section, you need a Semicolon.


SINGLE=0;

Turn off Single Mode. Network default is ON. 0=OFF  1=ON.
At the end of each section, you need a Semicolon.


LANG=en_GB;

Set the Language the VOICE comes back to you as.  en_GB=Servers Default.
At the end of each section you need a Semicolon.


Each section is separated, with a Semicolon. "Does not matter what order the above codes are in".